FIRE RESISTANT HALOGEN FREE POWER CABLES	Technical Data sheet

APPLICATIONS

(N)HXH FE180 PH30/E30 0,6/1 kV and (N)HXH-J FE180 PH30/E30 0,6/1 kV fire resistant and halogen free power cables, are intended for power supply to fire protection equipment in objects of sharp fire protection requirements, particularly in fire alarm and fire automatic control systems.

The cables shall be applied in locations where, in case of fire, higher safety for human beings and expensive electronic equipment is required.

Functions of the cables are maintained – power is supplied to equipment which must operate in fire conditions and during fire fighting (e.g. water pumps in fire extinguishing systems, smoke removing fans, emergency lighting and elevators).

The cables are certified by Scientific and Research Centre for Fire Protection - National Research Institute (Centrum Naukowo-Badawcze Ochrony Przeciwpożarowej - PIB) at Józefów.

The cables are flame retardant and their smoke emission is low, emitted fumes are non toxic and non corrosive.

The cables are suitable for fixed indoor and outdoor installations. UV radiation protection is required for outdoor installations. Laying cables in water or direct earth burial are only permitted if additional protection is used.

CONSTRUCTION                                                                                                           

• bare annealed copper conductors meeting requirements of PN-EN 60228 standard:

RE - class 1 single wire round conductor,

RM - class 2 multiwire round conductor,

• double special cross-linked silicone rubber insulation – colours:

            up to 5 wires in accordance with PN-HD 308,

            above 5 wires black and white conductor number printed on it,

green-yellow protective conductor in the outer layer in (N)HXH-J FE180 PH30/E30 0,6/1 kV cable,

• insulated conductors laid-up into a cable core,
• inner covering made of halogen free compound,
• orange cable sheath made of halogen free compound type HM4 according to HD 604 S1 and VDE 0276-604, (oxygen index bigger than 35%).

CHARACTERISTICS

Operating voltage    0.6/1 kV

Voltage test    4.0 kV rms

Insulation resistance at 90°C, minimum   10¹¹ Ω·cm

Inductance, approximate    0.7 mH/km

Conductor temperature limit
    in work conditions          +90°C
    in short-circuit               +250°C

Corrosivity of emitted gases per    PN-EN 60754-1, PN-EN 60754-2, IEC 60754-2

pH, approximate    6.8

conductivity, approximate    0.4 µS/mm

Smoke density per    PN-EN 61034-2, IEC 61034-2

light transmittance, minimum    70%

Operating temperature range
      during operation             from -30 to +90°C
      during installation           from   -5 to +50°C

Minimum bending radius:     

single core cables                   15 x cable diameter

multi core cables                    12 x cable diameter

Cable combustibility             fire resistant

Combustibility tests             PN-EN 60332-1-2, IEC 60332-1-2, PN-EN 60332-3-24, IEC 60332-3-24 (cat. C)

Circuit integrity ^*                           

             E30                     DIN 4102-12

             PH30                   PN-EN 50200 or PN-EN 50362

Insulation integrity FE180       IEC 60331-21, IEC 60331-11

Reference standards             AT-0603-0496/2016, WT-TK-44, DIN VDE 0266, PN-HD 604 S1

^*Circuit integrity is dependent on installation method.

Cable installation - Only certified cable fixing systems shall be used. Systems certified according to DIN 4102 part 12 are recommended.

The cable meets requirements of the low voltage directive 2014/35/EU

Other cross-sections and conductor counts available on request.

TECHNOKABEL S.A. reserves the right to change specifications without prior notice.